3D Printed Parts
Custom 3D Printed Parts / Support this site
** THESE ARE NOT CURRENTLY AVAILABLE...I AM ON ORDERS WITH THE MILITARY AND HAVE NO WAY TO PRODUCE AND SHIP PARTS**
To purchase any of my customer 3D Printed parts, just send me your mailing address, parts desired, and the total amount of money for the parts to one of these payment locations:
Paypal, Facebook, or Google Pay: noah.helterbrand@gmail.com
CashApp: $helterbrand
Venmo: WizardOfGunMonkeys
I typically ship by USPS, if you need me to use UPS or FedEx, or expedited shipping, let me know. Standard USPS shipping is included in the price, but UPS/FedEx/Expedited may be extra cost.
Part customization is also available for an extra cost if you need it printed in a custom color, adjust the mount dimensions, etc.
All parts are printed using high quality PETG which is both chemical resistant and UV resistant.
Currently available parts:
Door Quiet Kit - $20/25
My most popular item. Available for 2 and 4 door models. Replaces the poorly designed OEM door bushings with a much thicker bushing that helps prevent the door from rattling on the catch. This is the fix for the root of the problem some guys are putting electrical tape on the latch loops for. The kit also includes a spacer for the front window net tab, it tends to rattle on the bolt that holds it, the spacer locks it in place. Not only does this kit make the doors much quieter, but it also makes them open and close heavier, more like a car door.
Installs in around 20 minutes per door, nothing too special required.
This is a pre-finished kit for the parts posted here on Thingiverse, if you do not have access to a 3D printer.
Grill Lightbar Mount for 8 inch Lightbars - $50
Fits standard 8 inch Single-Row Amazon/Ebay units using M5 screws in the side
Installs in just a couple of minutes, no drilling required
The lightbar pictured is this one from eBay.
8 Gang Overhead Roll Bar Mount- $150*
Fits 8 gang Chinese switch units commonly found on Amazon/eBay. I use this one.
Dual voltage gauge for dual battery setups. Can be connected so both show same if you do not have dual batteries.
Left switch overrides Key-On power to allow connected accessories to be enabled without needing to key-on and run the fuel pump and ECU. Right switch turns voltage gauge on and off to prevent residual draining of batteries.
The 8 gang switch panel is not included, but the switches, voltage gauge, and wiring harness is, and I will pre-wire the switches and gauge to the harness for you. There are 4 wires in the harness:
1- Connects to primary battery side of isolator or winch cable (make sure winch cable is connected in battery box if you do not have a winch installed, you will need this for the 8 gang unit anyway)
2- Connects to secondary battery side of isolator (connect to primary side if single battery only)
3- Connects to common ground
4- Ties into key on power line going to 8 gang box.
*If you want to mount the switch panel only, without the gauge and switch functions, I will send you the lower half only for $30. It will have mounting tabs on the back if you decide to upgrade to the switch/gauge later.
2 inch Roll Tube Mount - $see below
Fits 2 inch tubes and mount set for smaller lightbars or similar equipment using M5 screws
2 Pack - $15, additional pairs ordered at the same time are $10/pr
42 inch windshield Lightbar Mount- $20
Fits common single row 42 inch Amazon/eBay light bars tightly to the top of the windshield using the factory drilled holes in the tabs in the upper corners.
The one pictured here is this one from Amazon. It was around $75 when I bought it.
Not currently windshield compatible. This should mainly be used if you are running a half windshield or no windshield.
If you are super motivated, and have a 3D printer, I have a few items available online that you can print. https://www.thingiverse.com/wizardofgunmonkeys/designs Please send coffee or beer if any of those helped you out.